Testing

Automated unit tests

WirePlumber has automated tests that you can easily run with:

$ meson test -C build

This will automatically compile all test dependencies, so you can be sure that this always tests your latest changes.

If you wish to run a specific test instead of all of them, you can run:

$ meson test -C build test-name

When debugging a single test, you can additionally enable verbose test output by appending -v and you can also run the test in gdb by appending --gdb.

For more information on how to use meson test, please refer to meson's manual

When submitting changes for review, always ensure that all tests pass

Please note that many WirePlumber tests require specific SPA test plugins to be available in your PipeWire installation. More specifically, PipeWire needs to be configured with the following options enabled:

-Dvideotestsrc=true -Daudiotestsrc=true -Dtest=true

If these SPA plugins are not found in the system, some tests will fail. This is expected.

WirePlumber examples

WirePlumber ships examples in test/examples. Execute them from the top-level directory like this:

$ WIREPLUMBER_MODULE_DIR=build/modules ./build/tests/examples/audiotestsrc-play

Assuming there is no other process actively using hw:0,0 from alsa, the above example should play a test tone on hw:0,0 without errors.

Native API clients

pw-cat

Using the default endpoint:

$ wpctl status  # verify the default endpoints
$ pw-record test.wav
$ pw-play test.wav

Using a non-default endpoint:

$ pw-record --list-targets  # find the node id
$ pw-record --target <node_id> test.wav
$ pw-play --list-targets  # find the node id
$ pw-play --target <node_id> test.wav

or

$ wpctl status  # find the capture & playback endpoint ids
$ pw-record --target <endpoint_id> test.wav
$ pw-play --target <endpoint_id> test.wav

Note: node ids and endpoint ids can be used interchangeably when specifying targets in all use cases.

video-play

Using the default endpoint:

$ cd path/to/pipewire-source-dir
$ ./build/src/examples/video-play

Using a non-default endpoint:

$ wpctl status  # find the endpoint id from the list
$ cd path/to/pipewire-source-dir
$ ./build/src/examples/video-play <endpoint_id>

Tip: enable videotestsrc in wireplumber's configuration to have more video sources available (see videotestsrc.node.disabled in the configuration directory)

PulseAudio compat API clients

pacat

Using the default endpoint:

$ wpctl status  # verify the default endpoints
$ pw-pulse parecord test.wav
$ pw-pulse paplay test.wav

Using a non-default endpoint:

$ wpctl status  # find the capture & playback endpoint ids
$ PIPEWIRE_NODE=<endpoint_id> pw-pulse parecord test.wav
$ PIPEWIRE_NODE=<endpoint_id> pw-pulse paplay test.wav

pavucontrol

$ pw-pulse pavucontrol
  • Volume level meters should work
  • Changing the volume should work

ALSA compat API clients

aplay / arecord

Note: unless you have installed PipeWire in the default system prefix (/usr), the ALSA compat API will not work, unless you copy libasound_module_pcm_pipewire.so in the alsa plugins directory (usually /usr/<libdir>/alsa-lib/) and that you add the contents of pipewire-alsa/conf/50-pipewire.conf in your ~/.asoundrc (or anywhere else, system-wide, where libasound can read it)

Using the default endpoint:

$ wpctl status  # verify the default endpoints
$ arecord -D pipewire -f S16_LE -r 48000 test.wav
$ aplay -D pipewire test.wav

Using a non-default endpoint:

$ wpctl status  # find the capture & playback endpoint ids
$ PIPEWIRE_NODE=<endpoint_id> arecord -D pipewire -f S16_LE -r 48000 test.wav
$ PIPEWIRE_NODE=<endpoint_id> aplay -D pipewire test.wav

or

$ wpctl status  # find the capture & playback endpoint ids
$ arecord -D pipewire:NODE=<endpoint_id> -f S16_LE -r 48000 test.wav
$ aplay -D pipewire:NODE=<endpoint_id> test.wav

JACK compat API clients

qjackctl

pw-jack qjackctl
  • This should correctly connect.
  • The "Graph" window should show the PipeWire graph.

jack_simple_client

$ wpctl status  # find the target endpoint id
$ wpctl inspect <endpoint_id>  # find the node.id
$ PIPEWIRE_NODE=<node_id> pw-jack jack_simple_client

The JACK layer is not controlled by the session manager, it creates its own links; which is why it is required to specify a node id (endpoint id will not work)

Device Reservation

with PulseAudio

  1. With PulseAudio running, start a pulseaudio client:
gst-launch-1.0 audiotestsrc ! pulsesink
  1. Start PipeWire & WirePlumber
    • The device in use by PA will not be available in PW
  2. Stop the PA client
    • A few seconds later, WirePlumber should assume control of the device
  3. wpctl status should be able to confirm that the device is available
  4. Start a PA client again
    • It should not be able to play; it will just freeze
  5. Stop WirePlumber
    • The PA client should immediately start playing

with JACK

  1. Start PipeWire & WirePlumber
    • All devices should be available
  2. Start jackdbus
    • through qjackctl:
      • Enable Setup -> Misc -> Enable JACK D-Bus interface
      • Click Start on the main window
    • or manually:
      • Run jackdbus auto
      • Run qdbus org.jackaudio.service /org/jackaudio/Controller org.jackaudio.JackControl.StartServer
  3. Wait a few seconds and run wpctl status to inspect
    • The devices taken by JACK should no longer be available
    • There should be two JACK System endpoints (sink & source)
  4. Run an audio client on PipeWire (ex pw-play test.wav)
    • Notice how audio now goes through JACK
  5. Stop JACK
    • through qjackctl, click Stop
    • or manually: qdbus org.jackaudio.service /org/jackaudio/Controller org.jackaudio.JackControl.StopServer
  6. Wait a few seconds and run wpctl status to inspect
    • The devices that were release by JACK should again be available
    • There should be no JACK System endpoint

You may also start WirePlumber after starting JACK. It should immediately go to the state described in step 3

The results of the search are